ASENPOWERRUBBER & SEALING SOLUTIONSRequest a Quote ↗

Home / Application Solutions / Automotive

APPLICATION SOLUTION

Rubber Components and Sealing Solutions for Automotive Systems

Review custom rubber components by vehicle system, heat, oil exposure, vibration, weathering and assembly conditions before requesting a quotation.

INCOMPLETE — image: Automotive assembly line application for custom rubber sealing components · Original source: https://asenpower.com/wp-content/uploads/2026/07/asenpower-industry-automotive-v1.jpg

EQUIPMENT AND SYSTEMS

Start with the vehicle system, not a generic product list.

The same rubber part can face very different risks depending on where it is installed and how the vehicle system operates.

01

Powertrain and Thermal

Review heat, oil, coolant contact, pressure change and assembly access.

02

Chassis and Suspension

Review vibration, repeated loading, movement, abrasion and environmental exposure.

03

Fluid Handling

Review media compatibility, hose or connector interfaces and leakage paths.

04

Electrical Enclosures

Review dust, water ingress, compression and long-term sealing force.

05

Body and Interior

Review noise isolation, weathering, fit, touch points and assembly tolerances.

ENGINEERING CHALLENGES

Automotive rubber parts must balance environment, movement and assembly.

These conditions should be reviewed together before material, geometry and production route are defined.

01

Heat and Fluid Exposure

Engine oil, fuel, coolant or cleaning media can change material direction.

02

Vibration and Repeated Load

Mounts, bushings and protective components may require fatigue and fit review.

03

Dust and Water Ingress

Outdoor and underbody locations require weathering and interface review.

04

Movement and Wear

Dynamic contact, flexing and repeated travel can create abrasion or cracking risk.

05

Assembly Tolerance

Mating parts, compression, fasteners and installation sequence affect sealing performance.

RECOMMENDED PRODUCTS

Components commonly reviewed for automotive systems.

Product selection follows the installation interface and operating conditions. Final suitability depends on the project drawing and compound.

MATERIAL DIRECTION

Choose material from media, temperature, motion and weather exposure.

Material names alone do not define performance. Review the specific compound and operating conditions before approval.

NBR

Often reviewed for oil contact and general industrial sealing.

FKM

Often reviewed for heat, oil, fuel and chemical exposure.

EPDM

Often reviewed for weather, water and outdoor sealing.

Silicone

Often reviewed for flexibility and broad temperature exposure.

HNBR

Often reviewed for demanding oil, heat and wear conditions.

MANUFACTURING EVIDENCE

Connect the drawing to production and inspection evidence.

Manufacturing evidence should show how geometry, repeat production and critical dimensions are controlled for the project.

INCOMPLETE — image: ASENPOWER production line for custom rubber parts manufacturing · Original source: https://asenpower.com/wp-content/uploads/2026/07/asn-home-production-line-2-1-1.jpg

Production Route Review

Molding and production planning are reviewed against geometry, quantity and part handling.

INCOMPLETE — image: Dimensional inspection of custom rubber components at ASENPOWER · Original source: https://asenpower.com/wp-content/uploads/2026/07/asenpower-manufacturing-dimensional-inspection-v2-1.webp

Dimensional Inspection

Critical dimensions and inspection requirements should be defined from the drawing before production.

QUALIFIED RFQ

What information helps an automotive application review?

Send enough system information to connect the component to its real installation and failure risk.

  • Vehicle system and installation position
  • Drawing, sample photo or mating-part dimensions
  • Temperature and media exposure
  • Static, rotating, reciprocating or flexing movement
  • Current failure mode or service concern
  • Prototype quantity and annual forecast

Start Engineering Review

Use the RFQ form to send drawings and operating conditions. Contact ASENPOWER before sending sensitive files if specific confidentiality terms are required.

ENGINEERING FAQ

Questions engineers ask before an automotive RFQ.

Answers remain conditional because final material and design decisions depend on the specific compound, geometry and vehicle system.

Can you review a non-standard rubber part?

Yes. Send the drawing, installation interface, operating conditions and quantity for manufacturing review.

Which material is best for oil and heat?

NBR, HNBR or FKM may be considered, but the media, temperature, duration and movement must be reviewed.

Can outdoor weathering affect the material choice?

Yes. Ozone, sunlight, water and temperature cycling can influence material and protective design decisions.

What should I send if the current part is failing?

Provide failure photos, service conditions, mating dimensions and any change in media, load or assembly.

APPLICATION REVIEW

Have an automotive sealing or vibration-control challenge?

Send the drawing and vehicle-system conditions so the component, material and manufacturing route can be reviewed together.

Send us your drawings, specifications or project requirements for engineering review.

Send Your Drawing