ASENPOWERRUBBER & SEALING SOLUTIONSRequest a Quote ↗
MATERIALS & ENGINEERING

Choose the Right Rubber Material for Your Application

ASENPOWER reviews service temperature, media compatibility, movement, environment and documentation needs before recommending a material direction.

INCOMPLETE — image: Rubber material testing and inspection equipment used for engineering review · Original source: https://asenpower.com/wp-content/uploads/2026/07/materials-v2-engineering-evidence-composite-v1.png

Material Decision Tool

Answer five operating-condition questions to build a practical material shortlist before engineering review.

Working Temperature

What are the minimum, continuous and peak temperatures?

Media

Will it contact oil, fuel, water, steam or chemicals?

Dynamic or Static?

Is the seal static, reciprocating, rotary or exposed to pressure cycling?

Food-Contact Documentation?

Do you need project-specific food-contact documentation for the exact compound?

Outdoor?

Will ozone, UV, weather, water or outdoor exposure affect the part?

Recommended Materials

Shortlist NBR, EPDM, FKM, Silicone, HNBR or PTFE, then confirm the grade.

Application Requirements

Start with service temperature, media contact, environment, seal motion and compliance requirements. These inputs narrow the material options before engineering review.

Temperature

Check continuous, peak and low-temperature recovery.

Chemical Resistance

Identify every fluid, cleaner and concentration.

Pressure

Review extrusion risk, seal geometry and pressure cycling.

Movement

Define speed, stroke, friction and wear conditions.

Regulatory

Require a verified compound and applicable documentation.

Outdoor Environment

Confirm ozone, sunlight, water and outdoor exposure.

Material Comparison Matrix

Compare NBR, EPDM, FKM, Silicone, HNBR and PTFE across service temperature, oil, fuel, weather, chemicals, wear, compression set, sealing behavior and relative cost. Final selection depends on compound grade and service conditions.

INCOMPLETE — image: Comparison matrix for NBR, EPDM, FKM, silicone, HNBR and PTFE material properties · Original source: https://asenpower.com/wp-content/uploads/2026/07/materials-v2-comparison-matrix.png

NBR Rubber

Best for: Oil-contact seals and general industrial components.
Temperature: Typical range: -30 to +120 C.
Oil / fuel: 4 / 5   Weather / ozone: 2 / 5
Limitation: Not first choice for ozone, weather, or many polar fluids.

EPDM Rubber

Best for: Water, steam, brake-fluid and outdoor sealing review.
Temperature: Typical range: -45 to +150 C.
Oil / fuel: 1 / 5   Weather / ozone: 5 / 5
Limitation: Generally unsuitable for petroleum oils and hydrocarbon fuels.

FKM Rubber

Best for: Heat, fuels and demanding chemical exposure.
Temperature: Typical range: -20 to +200 C.
Oil / fuel: 5 / 5   Weather / ozone: 5 / 5
Limitation: Higher cost and compound-specific low-temperature limits.

Silicone Rubber

Best for: Wide-temperature and clean-application review.
Temperature: Typical range: -60 to +230 C.
Oil / fuel: 2 / 5   Weather / ozone: 5 / 5
Limitation: Lower tear and abrasion resistance; oil use needs review.

HNBR Rubber

Best for: Higher-duty oil, heat and dynamic sealing.
Temperature: Typical range: -30 to +150 C.
Oil / fuel: 5 / 5   Weather / ozone: 4 / 5
Limitation: Higher cost and fewer standard compound options.

PTFE

Best for: Low-friction, chemical and wide-temperature applications.
Temperature: Typical range: -200 to +260 C.
Oil / fuel: 5 / 5   Weather / ozone: 5 / 5
Limitation: Not elastomeric; creep, filler and seal design require review.

Not Sure Which Material Fits Your Drawing?

Send your application details, operating conditions, or drawing for an engineering material review.

Popular Materials

Compare strengths, limits and typical applications before opening the full material profile.

INCOMPLETE — image: NBR rubber O-rings and standard sealing parts on a light background · Original source: https://asenpower.com/wp-content/uploads/2026/07/materials-v2-nbr-standard-parts-v1.jpg

NBR

Best for oil and fuel sealing at moderate temperatures. Avoid ozone and prolonged outdoor exposure.

INCOMPLETE — image: EPDM rubber sealing parts and sheet samples · Original source: https://asenpower.com/wp-content/uploads/2026/07/materials-v2-epdm-standard-parts-v1.jpg

EPDM

Excellent for weather, ozone, water and steam. Not recommended for petroleum oils.

INCOMPLETE — image: FKM rubber O-rings and high-temperature sealing parts · Original source: https://asenpower.com/wp-content/uploads/2026/07/materials-v2-fkm-standard-parts-v1.jpg

FKM

High-temperature and chemical resistance for fuels and aggressive media. Higher relative cost.

INCOMPLETE — image: Silicone rubber seals and standard molded parts · Original source: https://asenpower.com/wp-content/uploads/2026/07/materials-v2-silicone-standard-parts-v1.jpg

Silicone

General temperature flexibility depends on compound and operating conditions. Limited abrasion resistance.

INCOMPLETE — image: HNBR rubber sealing rings and molded components · Original source: https://asenpower.com/wp-content/uploads/2026/07/materials-v2-hnbr-standard-parts-v1.jpg

HNBR

Higher strength, heat and oil resistance for demanding dynamic seals. Moderate weather resistance.

INCOMPLETE — image: PTFE sealing rings and machined components · Original source: https://asenpower.com/wp-content/uploads/2026/07/materials-v2-ptfe-standard-parts-v1.jpg

PTFE

Low friction and broad chemical resistance across extreme temperatures. Rigid rather than elastic.

ENGINEERING REFERENCE

Temperature Performance Chart

Typical engineering reference ranges: NBR -30 to 100 C; EPDM -50 to 150 C; FKM -20 to 220 C; Silicone -60 to 230 C; HNBR -40 to 150 C; PTFE -200 to 260 C. Final limits depend on compound and service conditions.

INCOMPLETE — image: Service temperature comparison chart for common rubber and PTFE materials · Original source: https://asenpower.com/wp-content/uploads/2026/07/materials-v2-temperature-chart.png

INCOMPLETE — image: Chemical resistance guidance for NBR, EPDM, FKM, silicone, HNBR and PTFE · Original source: https://asenpower.com/wp-content/uploads/2026/07/materials-v2-chemical-guide.png

MEDIA COMPATIBILITY

Chemical Resistance Guidance

Oil: NBR, FKM or HNBR. Water and steam: EPDM. Fuels and aggressive chemicals: FKM or PTFE. Food-contact requirements must be stated in the RFQ; availability is confirmed per project. Confirm concentration, temperature and exposure time.

ENGINEERING REVIEW INPUTS

Testing and Documentation Review

Where the project requires testing or documentation, include the method, acceptance criteria and required records in the RFQ. Test reports or certificates must be confirmed in writing before quotation.

Physical-Property Scope

Hardness, tensile, elongation or other checks are defined only when relevant to the project.

Project Documentation

Applicable records must be confirmed for the exact material and quotation scope.

Material Selection FAQ

Practical starting points for common material-selection questions. Final recommendations remain subject to drawing and application review.

How do I choose between NBR and FKM?
Use NBR for cost-effective oil resistance at moderate temperatures. Choose FKM when higher heat, fuels or aggressive chemicals require stronger resistance.
Which rubber material is best for outdoor use?
EPDM is the usual starting point for ozone, UV, water and outdoor weathering. Suitable silicone grades can support wider temperature ranges when the application requires them.
What material works with oil and fuel?
NBR suits many moderate oil applications. HNBR adds heat and mechanical strength, while FKM is preferred for fuels, higher temperatures and more aggressive media.
Can you recommend a material from my drawing?
Yes. Send the drawing with media, temperature, pressure, motion, tolerance and quantity so the engineering team can recommend a suitable material before quotation.
Can you match an existing rubber sample?
Yes. Existing samples can be reviewed and tested for hardness and physical properties. Final matching remains subject to verification against the real service conditions.
Do you provide food-grade or compliant materials?
If you require food-contact, FDA, LFGB or medical-grade documentation, state the requirement in the RFQ. Availability of materials, tests and documentation is confirmed per project; certification is not promised.
Can you manufacture custom compounds?
Custom compounds can be developed for defined hardness, color, physical performance or compliance needs, subject to project volume and engineering review.
What information is needed for material selection?
Provide the drawing or CAD file, exact media, temperature, pressure, static or dynamic motion, critical tolerance, annual quantity and required compliance.

Need Help Choosing the Right Material?

Share your drawing, operating temperature, contact media, application environment and annual quantity. Our engineers will review material fit before quotation.

NDA protected. Engineering review. Material recommendation. Fast response. Global delivery.

Send us your drawings, specifications or project requirements for engineering review.

Send Your Drawing

General industry / literature reference only: temperature ranges, material comparisons and handbook fits (including h11, H8, Ra, hardness and chamfer) are confirmed per compound and project, not an ASENPOWER guarantee. Material recommendations are starting points for project review.