ASENPOWERRUBBER & SEALING SOLUTIONSRequest a Quote ↗

NBR vs FKM: How to Choose Rubber Materials for Sealing Applications

NBR and FKM are two of the most common elastomers considered for industrial sealing parts. Both can be useful, but they solve different problems. Choosing between them should start with the application environment, not only the material name on a drawing.

What Is NBR?

NBR, also called nitrile rubber, is widely used for oil seals, O rings, gaskets, diaphragms and molded rubber components. It is often selected when the part will contact petroleum-based oils, hydraulic fluids, grease or fuel-related environments. NBR is also attractive when the project needs a practical balance of cost, mechanical strength and availability.

For OEM programs, NBR is often the first material reviewed when the sealing environment is moderate and the main concern is resistance to oil. It can be molded into custom rubber parts, cut into gaskets or used for standard and custom O rings.

What Is FKM?

FKM is a fluoroelastomer used where heat, chemical exposure or fuel resistance is more demanding. It is commonly considered for engines, pumps, valves, oil and gas equipment, industrial machinery and sealing systems exposed to elevated temperatures.

FKM is usually more expensive than NBR, but that cost can be justified when premature hardening, swelling or compression set would create maintenance problems. The decision should be based on total sealing risk rather than part price alone.

Oil and Fuel Resistance

NBR performs well in many oil and grease environments. It is a practical material for hydraulic seals, O rings and general industrial gaskets where operating temperature and chemical exposure remain within the material range.

FKM is usually preferred when the seal must handle fuels, aggressive oils, additives or elevated temperature at the same time. In harsh service, FKM may retain sealing properties longer than NBR.

Temperature Considerations

Temperature is one of the fastest ways to separate NBR and FKM. NBR is suitable for many moderate environments, while FKM is typically considered for higher temperature exposure. The exact usable range depends on compound design, hardness, media and part geometry.

For custom rubber parts, always review continuous temperature, short peak temperature and nearby heat sources. A part that only briefly contacts high temperature may have different requirements from a seal operating continuously near its limit.

Chemical Compatibility

Neither material should be selected by name alone. NBR and FKM both have strengths, but chemical compatibility depends on the exact fluid, concentration, temperature and exposure time. Cleaning chemicals, additives and process fluids can change the recommendation.

When the application includes unknown chemicals, provide the full media list during RFQ. Material review becomes more reliable when the supplier knows the actual working environment.

Cost and Availability

NBR is often more economical and easier to source for broad industrial use. FKM usually costs more, but it can reduce failure risk in demanding environments. For OEM purchasing, the right question is not which material is cheaper. The better question is which material provides acceptable performance with stable supply and reasonable lifetime cost.

When to Choose NBR

  • Petroleum oil, grease or hydraulic fluid contact is the main requirement.
  • Operating temperature is moderate.
  • The design needs a practical cost-performance balance.
  • The component is a gasket, O ring, molded rubber part or oil-resistant seal.

When to Choose FKM

  • The application has elevated temperature.
  • The seal contacts fuels, aggressive oils or demanding chemical media.
  • Long service life is more important than lowest piece price.
  • The equipment has high maintenance cost if a seal fails.

Related ASENPOWER Products

Material decisions often connect directly to part design. Review O Rings, Custom Rubber Parts, Rubber Gaskets and Hydraulic Seals when comparing NBR and FKM for production.

Engineering Review Checklist

Before finalizing a sealing part or rubber component, review the working environment, mating hardware, motion, pressure, temperature, media and inspection expectations together. A material that looks correct in a table can still fail if the groove, compression, surface finish or installation process is wrong.

For supplier review, prepare the drawing revision, 2D or 3D files, sample photos, material target, hardness, operating media, temperature range, annual quantity, prototype needs and any known failure history. If the current design is replacing an existing part, include the reason for replacement and any field issues observed by maintenance teams.

Send Drawings for Engineering Review

If your project requires a custom material, unusual geometry, non-standard tolerance or application-specific sealing performance, prepare drawings, samples, material notes and annual quantity estimates before requesting a quote. ASENPOWER can review custom rubber parts, hydraulic seals, PTFE components, O rings and industrial gaskets for OEM equipment programs.

Request a Quote or send your drawing for review.

Send us your drawings, specifications or project requirements for engineering review.

Send Your Drawing

General industry / literature reference only: temperature ranges, material comparisons and handbook fits (including h11, H8, Ra, hardness and chamfer) are confirmed per compound and project, not an ASENPOWER guarantee. Material recommendations are starting points for project review.