ASENPOWERRUBBER & SEALING SOLUTIONSRequest a Quote ↗

PTFE Seals Material Guide: Grades, Properties & Applications

PTFE is the outlier of the sealing world: a plastic that behaves like no rubber, with near-universal chemical resistance, an extremely low friction coefficient, and a service range from cryogenic cold to 200°C and beyond. But pure PTFE has a weakness — cold flow (creep) — which is why real-world PTFE seals are almost always filled compounds, not virgin PTFE.

This guide covers PTFE grades, what each filler does, where PTFE beats rubber, and how to specify it in an RFQ.

What Makes PTFE Different

PTFE (polytetrafluoroethylene) is a fluoropolymer with a carbon backbone fully shielded by fluorine atoms. The result:

  • Friction coefficient ~0.05–0.10 — the lowest of any solid, enabling dry-running seals
  • Chemical resistance — inert to nearly all industrial chemicals, acids, and solvents
  • Temperature range — roughly −60 °C to +200 °C continuous (short peaks higher)
  • Non-stick, non-aging — does not harden, crack, or take a compression set the way rubber does

The trade-off: PTFE has almost no elasticity. It cannot energize itself like a rubber O-ring — PTFE seals need mechanical energizing (springs, O-ring expanders) or interference fits designed around its stiffness.

Virgin PTFE vs Filled PTFE

Virgin (unfilled) PTFE is soft, creeps under load (cold flow), and wears quickly in dynamic service. It is fine for static gaskets and chemical linings — but a poor choice for a dynamic seal.

Filled PTFE blends PTFE with reinforcing fillers that dramatically improve wear resistance, creep resistance, thermal conductivity, and hardness — at some cost to chemical inertness and elongation. Every serious PTFE seal you buy is a filled compound.

Common Filled PTFE Grades

Filler (typical %) What it improves Watch-outs Typical uses
Glass fiber (15–25%) Creep resistance, wear, compressive strength Abrasive to soft mating surfaces Hydraulic piston seals, wear rings
Carbon / graphite (15–25%) Wear life, thermal conductivity, low friction Dark color; not for food contact in some regs Compressor rings, high-speed rotary seals
Bronze (40–60%) Creep resistance, thermal conductivity, wear Attacked by some acids; heavy Hydraulic seals, high-load bearings
Graphite (5–15%) Low friction, dry-running ability Lower strength than glass/carbon Dry-running rotary seals
MoS₂ (molybdenum disulfide) Break-in lubricity, wear Gray color; limited high-temp use Startup-critical dynamic seals

Temperature and Chemical Resistance

PTFE compounds typically serve from −60 °C to +200 °C continuous, with short excursions higher. Chemically, PTFE resists virtually all acids, bases, solvents, and fuels. The rare exceptions: molten alkali metals (sodium, potassium) and fluorine compounds at elevated temperature — if your process involves these, say so explicitly, because standard PTFE is not the answer.

PTFE vs Rubber Seals: When to Choose Which

Factor PTFE wins when… Rubber wins when…
Temperature Above ~150 °C continuous, or cryogenic Within −40…+120 °C (NBR/FKM range)
Chemical media Aggressive chemicals, strong acids/solvents Standard oils, fuels, water
Speed / dry running High surface speed or dry/marginal lubrication Lubricated, moderate speed
Cost & volume — Lower piece price, high-volume molding
Elasticity needed — Static sealing, squeeze-type designs (O-rings)

Common PTFE Seal Forms

  • Piston and rod seals — wear rings and guide rings in hydraulic cylinders (often bronze- or glass-filled)
  • Spring-energized lip seals — a PTFE jacket with a metal spring energizer for rotary and reciprocating service
  • V-packings / chevron sets — stacked PTFE rings for high-pressure reciprocating rods
  • PTFE-envelope gaskets and O-rings — a PTFE jacket over an elastomer core, combining chemical resistance with rubber-like squeeze

Design Notes for Engineers

  • Groove design differs from rubber. PTFE needs room for thermal expansion — size grooves per the supplier’s data, not per O-ring tables.
  • Protect during installation. PTFE jackets nick easily; use lead-in chamfers and installation sleeves, and never stretch a PTFE seal over sharp threads.
  • Mind the mating surface. Glass-filled grades are abrasive — pair them with hardened shafts (or accept faster shaft wear).
  • Account for cold flow in static designs. Bolted PTFE gaskets need controlled compression and sometimes re-torquing.

RFQ Checklist for PTFE Seals

  • Seal form and dimensions (or drawing / sample)
  • PTFE grade / filler required (or describe media + temperature and let the supplier recommend)
  • Operating media, temperature range, pressure, speed
  • Static or dynamic service; dry-running or lubricated
  • Mating surface material and hardness
  • Annual volume and target price

FAQ

Can PTFE replace a rubber O-ring?
Sometimes — PTFE-envelope O-rings do exactly this for chemical service. But a solid PTFE ring won’t seal like rubber without proper groove design and energizing; don’t drop it into an O-ring groove and expect the same behavior.

How do I choose a filled PTFE grade?
Start from the failure mode you fear most: wear → carbon/graphite; creep under load → glass or bronze; heat buildup → bronze or carbon for conductivity. Describe your media and temperature to the supplier and let them recommend.

PTFE is not automatically food-contact compliant. If you require food-contact, FDA, LFGB or medical-grade documentation, state the requirement in the RFQ. Availability of materials, tests and documentation is confirmed per project; certification is not promised.

Get PTFE Seals Quoted

Tell us your media, temperature, and seal form — we’ll recommend the grade and quote it. Request a quote.

Leave a Reply Cancel reply

NOT CONNECTED — this snapshot form is unavailable locally. Review the disabled quote form. Nothing is sent or stored.

Send us your drawings, specifications or project requirements for engineering review.

Send Your Drawing

General industry / literature reference only: temperature ranges, material comparisons and handbook fits (including h11, H8, Ra, hardness and chamfer) are confirmed per compound and project, not an ASENPOWER guarantee. Material recommendations are starting points for project review.