FKM Seals Material Guide: Grades, Properties & Applications
FKM is the workhorse of the premium elastomer world: a rubber that behaves like a chemical-resistant plastic, with heat resistance no standard rubber can touch and near-immunity to oils, fuels, and aggressive fluids. It is the default answer when NBR starts failing — in hot engines, fuel systems, and chemical plants.
But FKM has two weaknesses — cold performance and cost — which is why the material comes in several grades, and why picking the right one matters more than picking FKM itself.
This guide covers FKM grades, where FKM beats NBR (and where PTFE beats FKM), and how to specify it in an RFQ.
What Makes FKM Different
FKM (fluoroelastomer; “Viton” is Chemours’ brand name for it) is a rubber whose polymer backbone is heavily shielded by fluorine atoms — the same chemistry trick that makes PTFE so inert, but in an elastic form. The result:
- Heat resistance — roughly −20 °C to +200 °C continuous (short peaks to ~230–250 °C), far beyond NBR’s ~120 °C ceiling
- Fluid resistance — outstanding against mineral oils, fuels, lubricants, hydraulic fluids, and many acids and solvents
- Low compression set and aging — seals stay elastic for years in hot service instead of hardening and cracking
- Very long shelf life — up to 20 years under proper storage, the longest of any common seal elastomer
The trade-offs: FKM seals cost several times more than NBR, stiffen badly below about −20 °C (standard grades), and are attacked by a short list of specific chemicals — amines, ketones, esters, and strong alkalis. Know that list before you specify it.
Standard FKM vs Specialty FKM
Standard FKM (Type A / Type B, bisphenol-cured) covers the vast majority of sealing work: O-rings, oil seals, and gaskets in hot oil, fuel, and general chemical service. This is what most buyers mean when they say “FKM.”
Specialty FKM exists for the edges standard FKM can’t reach: low-temperature grades (GLT/GFLT, usable to about −40 °C), high-fluorine grades (Type F/GF, ~70% fluorine, for the most aggressive chemicals), and peroxide-cured grades (better steam and acid resistance, cleaner extraction profile for food and pharma-adjacent uses).
Common FKM Grades
| Grade (fluorine %) | What it improves | Watch-outs | Typical uses |
|---|---|---|---|
| Type A (~66%) | General heat + oil/fuel resistance; lowest cost FKM | Standard cold limit (~−20 °C) | O-rings, oil seals, gaskets — the default FKM |
| Type B (~68%) | Better fluid resistance than A at high temperature | Slightly higher cost | Hot oil, transmission, engine seals |
| Type F / GF (~70%) | Best chemical resistance, highest heat ceiling | Stiffest; highest price | Aggressive chemical processing, aerospace |
| GLT / GFLT (low-temp) | Usable to about −40 °C | Lower heat ceiling than standard grades | Cold-climate automotive, outdoor hydraulics |
| Peroxide-cured | Steam, acid, and amine resistance; low extractables | Needs post-cure; longer lead time | Food/pharma-adjacent, steam service |
Temperature and Chemical Resistance
Standard FKM serves from about −20 °C to +200 °C continuous. Low-temperature grades extend the cold end to roughly −40 °C; the price is a lower hot end.
Chemically, FKM resists mineral oils, greases, diesel, gasoline, hydraulic fluids, silicone oils, and a wide range of acids and solvents. The hard no-go list: amines, ketones (acetone, MEK), esters, strong bases/alkalis, and hot steam (standard grades) — if your process involves these, say so explicitly in the RFQ, because a standard FKM seal will fail there. Peroxide-cured grades handle steam and some amines far better.
FKM vs NBR vs PTFE: When to Choose Which
| Factor | FKM wins when… | NBR wins when… | PTFE wins when… |
|---|---|---|---|
| Temperature | Hot oil/fuel service, ~120–200 °C | Within −40…+120 °C | Above ~150 °C continuous, or cryogenic |
| Chemical media | Oils, fuels, many acids/solvents | Standard oils, water, mild fluids | Aggressive chemicals beyond FKM’s list (but watch FKM’s no-go chemicals) |
| Cold end | — | Down to −40 °C easily | Down to −60 °C and below |
| Cost & volume | — | Lowest piece price, high-volume molding | — |
| Design | Standard rubber grooves (elastic) | Standard rubber grooves | Needs energized/spring designs, not plain squeeze |
(For PTFE’s full picture — filled grades, groove design, cold flow — see our PTFE seals material guide.)
Common FKM Seal Forms
- O-rings — the single most common FKM part; AS568 sizes off the shelf, custom sizes molded
- TC oil seals — FKM-lip rotary shaft seals for hot oil, gearboxes, and engines (see our oil seal selection guide)
- Gaskets and diaphragms — chemical and fuel-system static sealing
- Custom molded parts — valve seats, boots, bellows, and bonded metal-rubber components from your drawing (our OEM process)
Design Notes for Engineers
- Standard rubber groove design works. Unlike PTFE, FKM is a true elastomer — O-ring grooves, squeeze percentages, and stretch limits follow normal rubber practice.
- Mind the cold end. An FKM O-ring that seals perfectly at 150 °C can leak at −25 °C as the compound stiffens past its glass transition. Size the squeeze for the coldest service temperature, or step up to a GLT grade.
- Don’t confuse FKM with FVMQ. Fluorosilicone (FVMQ) is a different material — better cold flexibility, worse hot-oil and fuel resistance. Confirm which one your drawing calls out.
- Sharp edges cut FKM during installation. Use lead-in chamfers like any rubber seal, and keep FKM away from the no-go chemical list — no groove design saves a chemically incompatible compound.
RFQ Checklist for FKM Seals
- Seal form and dimensions (or drawing / sample)
- FKM grade required — or describe media + temperature and let the supplier recommend
- Operating media, temperature range (note the coldest point), pressure, speed
- Static or dynamic service; rotary shaft or reciprocating
- Any exposure to amines, ketones, esters, strong alkalis, or steam (say so explicitly)
- Annual volume and target price
FAQ
Is Viton the same as FKM?
Viton is Chemours’ brand name; FKM is the generic ASTM designation for the same fluoroelastomer family. In an RFQ, “FKM” is the safer term — it keeps you from being locked to one brand’s compound.
Can FKM replace NBR?
Technically yes in most cases — FKM does everything NBR does, hotter and longer. The question is cost: FKM runs several times the price of NBR. Upgrade only the seals that actually see heat, fuel, or aggressive media; leave the rest in NBR.
FKM or PTFE for chemical service?
FKM for elastic, squeeze-type seals (O-rings, oil seals) in oils, fuels, and moderate chemicals. PTFE when the media is beyond FKM’s resistance, temperatures exceed ~200 °C, or dry running is involved — accepting PTFE’s need for energized designs. See the PTFE guide for the full comparison.
Standard FKM is not automatically food-compliant. If you require food-contact, FDA, LFGB or medical-grade documentation, state the requirement in the RFQ. Availability of materials, tests and documentation is confirmed per project; certification is not promised.
Get FKM Seals Quoted
Tell us your media, temperature range, and seal form — we’ll recommend the grade and quote it. Request a quote.
Need Custom Rubber Components?
Send us your drawings, specifications or project requirements for engineering review.
General industry / literature reference only: temperature ranges, material comparisons and handbook fits (including h11, H8, Ra, hardness and chamfer) are confirmed per compound and project, not an ASENPOWER guarantee. Material recommendations are starting points for project review.